Toshiba Security Camera IK TF7P2 User Manual

INSTRUCTION MANUAL  
3 CCD COLOR CAMERA  
IK-TF7P2  
For Customer Use  
Enter below the Serial No.  
which is located on the  
bottom of the cabinet. Retain  
this information for future ref-  
erence.  
Model No.: IK-TF7P2  
Serial No.:  
FCC NOTICE  
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-  
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference when the equipment is operated in a commercial environment. This equipment  
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance  
with the instruction manual, may cause harmful interference to radio communications. Operation of this  
equipment in a residential area is likely to cause harmful interference in which case the user will be  
required to correct the interference at his own expense.  
USER-INSTALLER CAUTION:Your authority to operate this FCC verified equipment could be voided if  
you make changes or modifications not expressly approved by the party responsible for compliance to  
Part 15 of the FCC Rules.  
This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.  
Following information is only for EU-member states:  
In residential areas this product may cause radio interference, therefore this product must not be used  
in residential areas.  
Following information is only for EU-member states:  
The use of the symbol indicates that this product may not be treated as household waste.  
By ensuring this product is disposed of correctly, you will help prevent potential negative  
consequences for the environment and human health, which could otherwise be caused by  
inappropriate waste handling of this product. For more detailed information about the take-  
back and recycling of this product, please contact your supplier where you purchased the  
product or consult.  
This manual is made from recycled paper.  
 
Note the following instructions when installing.  
• Do not cover the product with any material.  
• Do not place the product on any confined Inflammable material such as a  
carpet or blanket.  
• Do not place the product in a narrow space, as this may cause heat to buildup  
inside the product.  
Failure to follow the above cautions may result in fire.  
Do not place the product in direct sunshine and/or high temperature.  
Temperature build up inside the product may result in fire.  
Avoid placing in humid, smoky, vaporized or dusty places.  
This may result in fire and/or electric shock.  
Do not point the lens directly at the sun and/or intensive light such as  
direct sunlight, etc.  
Focusing of the light may cause eye injury and/or fire.  
Ask your dealer to perform a periodical check and internal cleaning  
(approx. once every five years).  
Dust inside the product may result in fire. For check and cleaning cost, please  
consult your dealer.  
Disclaimer  
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by  
the user in any of the following cases:  
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether inten-  
tional or accidental; use under extreme operating conditions.  
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including  
but not limited to loss of expected income and suspension of business activities.  
3. Incorrect use not in compliance with instructions in this instruction manual.  
4. Malfunctions resulting from misconnection to other equipment.  
5. Repairs or modifications made by the user or caused to be made by the user and carried out by  
an unauthorized third party.  
6. Notwithstanding the foregoing, Toshiba’s/TAIS liabilities shall not, in any circumstances, exceed  
the purchase price of the product.  
Copyright and Right of Portrait  
There may be a conflict with the Copyright Law and other laws when a customer uses, displays,  
distributes, or exhibits an image picked up by the camera without permission from the copyright holder.  
Please also note that transfer of an image or file covered by copyright is restricted to use within the  
scope permitted by the Copyright Law. Customer is responsible for complying with all copyright laws.  
Protection of Personal Information  
Images taken by the camera that reveal the likeness of an individual person may be considered  
personal information. To disclose, exhibit or transmit those images over the internet or otherwise,  
consent of the person may be required.  
3
 
Limitation of Usage  
The product is not designed for any “critical applications.Critical applications” means life support  
systems, exhaust or smoke extraction applications, medical applications, commercial aviation,  
mass transit applications, military applications, homeland security applications, nuclear facilities or  
systems or any other applications where product failure could lead to injury to persons or less of life  
or catastrophic property damage. Accordingly, [Toshiba/TAIS] disclaims any and all liability arising  
out of the use of the product in any critical applications.  
TABLE OF CONTENTS  
1. CAUTIONS ON USE AND INSTALLATION .....5  
2. COMPONENTS ................................................5  
3. NAMES AND FUNCTIONS ..............................6  
4. CONNECTION..................................................7  
( 4 ) PROCESS ..............................................22  
(4. 1) Changing gamma correction........22  
(4. 2) Changing master pedestal...........22  
(4. 3) Changing R pedestal ...................22  
(4. 4) Changing B pedestal....................22  
(4. 5) Changing noise reduction ............22  
( 5 ) SHADING................................................23  
(5. 1) Changing V.SHAD. (Vertical Shading)  
correction mode ...........................24  
4. 1 Standard Connection ................................7  
4. 2 Cautions on Connection............................7  
4. 3 Connector Pin Assignments......................7  
4. 4 How to use “EMI core” ..............................8  
5. OPERATION.....................................................9  
(5. 2) Changing the manual V.SHAD. (Vertical  
Shading) correction setting.............24  
(5. 3) Changing C.SHAD. (Corner Shading)  
correction mode ...........................24  
(5. 4) Changing the manual C.SHAD. (Corner  
Shading) correction setting ............24  
5. 1 White Balance...........................................9  
5. 2 Gain ........................................................10  
5. 3 Shading Correction .................................10  
6. ITEMS CONTROLLED BY THE SCREEN  
DISPLAY.........................................................11  
( 6 ) SYNC......................................................25  
(6. 1) Adjusting horizontal phase...........25  
( 7 ) OPTION ..................................................25  
(7. 1) Changing serial communication  
baud rate......................................25  
( 8 ) Returning to factory settings...................25  
7. 3 Synchro. Scan Operation ........................26  
( 1 ) Setting by 1H ..........................................26  
( 2 ) Setting by the frame................................26  
7. 4 E. TRG (External trigger) ........................27  
( 1 ) 1P SNR (1 Pulse Trigger  
7. MODE SETTING BY ON SCREEN DISPLAY....12  
7. 1 Using the Menus.....................................12  
7. 2 Menus .....................................................13  
( 1 ) SHUTTER (Electronic shutter)................13  
(1. 1) Changing the setting in  
MANU mode.................................14  
(1. 2) Changing the setting in  
SS (synchro. scan) mode.............15  
(1. 3) Changing the setting in  
E.TRG mode................................16  
(1. 3. 1) Changing the setting in  
1P SNR mode...........................16  
(1. 3. 2) Changing the setting in  
Sync Non Reset).....................................27  
(1. 1) 1 Pulse Trigger SYNC-NON  
RESET Picture Output Timing .....27  
( 2 ) 1P SR (1 Pulse Trigger Sync Reset).......28  
(2. 1) 1 Pulse Trigger SYNC-RESET  
1P SR mode .............................17  
(1. 3. 3) Changing the setting in  
Picture Output Timing ..................28  
( 3 ) PW SNR (Pulse width trigger  
PW SNR mode .........................18  
(1. 3. 4) Changing the setting in  
PW SR mode............................19  
(1. 3. 5) Changing the setting in  
RR mode...................................19  
(1. 4) Changing each setting in  
SYNC-NON RESET)...............................29  
(3. 1) Pulse Width Trigger SYNC-NON  
RESET Picture Output Timing .....29  
( 4 ) PW SR (Pulse width trigger  
AUTO mode .................................20  
( 2 ) GAIN (Video gain)...................................20  
(2. 1) Changing the setting in GAIN.......20  
( 3 ) WHT BAL (White balance)......................21  
(3. 1) Changing the setting in AWB  
(Automatic White Balance) mode...21  
(3. 2) Changing the setting in MANU  
(Manual) mode.............................21  
SYNC-RESET)........................................30  
(4. 1) 1 Pulse Width Trigger SYNC-RESET  
Picture Output Timing ..................30  
( 5 ) RR (Reset restart)...................................31  
(5. 1) Long Term Exposure....................31  
(5. 2) Input Timing Chart Example.........31  
4
 
7. 5 Partial Read ............................................32  
( 1 ) Partial Scanning OFF  
8. INPUT OUTPUT SIGNAL SPECIFICATIONS 35  
9. CCD OUTPUT WAVEFORM TIMING CHART 36  
10.BEFORE MAKING A SERVICE CALL...........37  
11.SPECIFICATIONS ..........................................37  
12.EXTERNAL APPEARANCE DIAGRAM.........38  
(All pixels scanning)................................32  
( 2 ) Partial Scanning ON ...............................32  
( 3 ) When Partial Scanning Mode is ON .......33  
7. 6 External Sync..........................................34  
( 1 ) External sync signal polarity ...................34  
( 2 ) External sync frequency range ...............34  
( 3 ) Using the unit with external sync signal..34  
(3. 1) H (horizontal) phase adjustment..34  
This product is a 3CCD color camera with digital video output.  
1. CAUTIONS ON USE AND INSTALLATION  
• Handling the unit.  
• Avoid using or storing the camera in the follow-  
Do not drop, jolt, or vibrate, as this may result in  
damage to the unit and may cause problems.  
ing places:  
Places filled with highly flammable and corrosive gas.  
Treat the camera cables carefully to prevent cable  
problems, such as breaks in the cable and loose  
connections.  
Places near gasoline, benzene, or paint thinner.  
Places subject to strong vibration.  
Places containing chemicals (such as pesticides),  
rubber or vinyl products for extended periods of time.  
• Install the camera in a location free from noise.  
If the camera or the cables are located near power  
utility lines or a TV, etc. undesirable noise may  
appear on the screen. In such a case, try to change  
the location of the camera or the cable wiring. Con-  
sult with a service personnel, if the noise still appears  
after changing the location or the cable wiring.  
• Do not shoot intense light.  
If there is an intense light at a location on the screen  
such as a spot light, a blooming and smearing may  
occur. When intense light enters, vertical stripes  
may appear on the screen. This is not a malfunction.  
Ghosts may occur when there is an intense light near  
the object. In this case, change the shooting angle.  
• Operating ambient temperature and humidity.  
Do not use the camera in places where temperature  
and humidity exceed the specifications. Picture  
quality will deteriorate and internal parts may be  
damaged.  
• Moire  
A moire pattern is an interference pattern generated  
when two repetitive line patterns overlap. This is not  
a malfunction. Eliminating the repetitive line patterns,  
or aligning the two patterns, will eliminate the moire.  
Be particularly careful when using in places exposed  
to direct sunlight. When shooting in hot environ-  
ments, depending on the conditions of the object and  
the camera (for example when the gain is increased),  
noise in the form of vertical strips or white dots may  
occur. This is not a malfunction.  
• Handling of the protection cap.  
Keep the protection cap away from children as they  
may pose a choking hazard. The protection cap  
protects the image sensing plane when the lens is  
removed from the camera head, do not discard.  
• When not using the camera for extended periods  
of time.  
Switch the control unit off and disconnect the power  
supply.  
• When cleaning the camera.  
Unplug the power source before cleaning. Clean with  
a soft dry cloth only. Do not use chemicals or chemi-  
cally treated cloths. Chemicals may damage coatings  
and printed letters. When cleaning the lens, use lens  
cleaning paper.  
2. COMPONENTS  
(1) Camera Control Unit......................................................................................................................1  
(2) Accessories  
(a) Instruction manual .................................................................................................................. 1  
(b) EMI core ................................................................................................................................. 1  
5
 
3. NAMES AND FUNCTIONS  
9
2
4
DC IN 12V terminal  
DISP button  
1 Prism faceplate  
MENU UP button  
(AWB)  
DISP  
6
7
DATA UP (AWB) button  
DATA DOWN button  
MENU DATA  
DC IN 12V  
PAGE  
5 MENU DOWN button  
8
DIGITAL terminal  
3 PAGE button  
[ Front ]  
[ Rear ]  
11  
10  
[ Bottom ]  
Prism faceplate  
The protection cap is attached on the lens mount portion. After removing the cap,  
mount the lens. Be careful not to scratch or touch the optical area.  
DISP button  
Used when switching the display.  
c PAGE button  
Used when switching to the menu and when selecting the menus.  
Select the function to be confirmed or changed on the menu.  
Select the function to be confirmed or changed on the menu.  
d MENU UP button  
e MENU DOWN button  
f DATA UP (AWB) button Changes the value of the function selected by the MENU (UP/DOWN) button. (Also  
used when using AWB.)  
g DATA DOWN button  
Changes the value of the function selected by the MENU (UP/DOWN) button.  
h DIGITAL terminal  
8-bit RGB, digital signal, and sync signals are output in the Camera Link format.  
Trigger signal and external sync signal (HD, VD) are inputs.  
Mode switching signal for partial scanning is input.  
Accepts serial communication control signals and a DC power input (12V).  
i DC IN 12V terminal  
j Mounting holes M3  
k Mounting holes M2  
Accept a DC power input (12V).  
Used to mount the camera.  
Used to mount the camera.  
6
 
4. CONNECTION  
4. 1 Standard Connection  
Lens  
Cable (not included)  
DC IN 12V  
IK-TF7P2  
Frame grabber board,  
Monitor  
Less than 4 mm  
image process  
equipment etc.  
DC power  
supply  
4. 2 Cautions on Connection  
• When connecting the camera cables, be sure to unplug the power source of the camera and the other equip-  
ment connected to it.  
• We suggest using a C mount lens made for a 3CCD color camera.  
When using another lens, the best camera performance of this camera may not be obtained.  
(For example, low resolution may occur, focus may be lost through the range of a zoom lens, and flare, ghost  
or shading may occur)  
Furthermore, in order to avoid damaging the mounting portion of the camera head, use a lens which has  
projection dimension from the mounting base of less than 0.157”(4mm).  
• The camera may be powered in two ways:  
(1) Supplied to the DC IN 12V terminal  
• For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA approved unground-  
ing type AC adaptor with the specifications described below.  
Power supply voltage : DC12V±10%  
Current rating  
Ripple voltage  
Connector  
: More than 830 mA  
: Less than 50 mV(p–p)  
: HR10A–7P–4S by HIROSE electronics Co. Ltd  
Pins 1, 2 : 12V  
Pins 3, 4 : GND  
• For DC power supply connecting to DC IN 12V terminal, use class II DC power supply approved accord-  
ing to EN60950-1 in Europe.  
(2) Supplied to the DIGITAL terminal  
• Supply the DC power supply (DC10V-DC13V) to pins 1 and 26 of the cable (sold separately).  
• When using PoCL (power over camera link) to power the camera, use a standard PoCL cable.  
* Use only one power supply type at a time.  
4. 3 Connector Pin Assignments  
DC IN 12V  
DIGITAL  
Function  
I/O  
O
O
O
O
O
I
O
I
I
I
I
1
2
3
4
+12V  
1
2
3
4
5
6
7
8
9
+12V  
14 GND  
15 X0+  
16 X1+  
17 X2+  
18 Xclk+  
19 X3+  
13  
26  
1
+12V  
GND  
GND  
X0-  
X1-  
X2-  
Xclk-  
X3-  
14  
Connector used:  
12226-51000-00  
(3M) or equivalent.  
1
2
3
4
SerTC+ 20 SerTC-  
SerTFG- 21 SerTFG+ Serial communication control (TXD)  
CC1-  
Serial communication control (RXD)  
22 CC1+  
23 CC2-  
24 CC3+  
25 CC4-  
26 +12V  
Trigger pulse input  
Partial scanning control  
External HD input  
External VD input  
10 CC2+  
11 CC3-  
12 CC4+  
13 GND  
Connector used:  
HR10A-7P-4PB  
(HIROSE electronics  
Co. Ltd) or equivalent.  
7
 
4. 4 How to use “EMI core”  
An EMI core is shipped with this camera.  
When power is supplied to the DC IN terminal, this part must be used as in the drawing below.  
If not used, unnecessary radio waves may be emitted.  
DC IN terminal  
Power cable: 2 turns  
Camera  
EMI core  
* Mount this core as close as possible to the camera.  
8
 
5. OPERATION  
Refer to the item “ 4. CONNECTION”, connect each component correctly.  
Turn on the power source of the connected equipment and the camera.  
c Point the lens at the object, adjust the lens iris, focus, etc..  
d Refer to the item “5.1 White Balance”, to do the adjustment.  
e Refer to the items “5.2 Gain, 7. MODE SETTING BY ON SCREEN DISPLAY”, select the necessary items.  
5. 1 White Balance  
For the white balance adjustment of this unit, AWB (Automatic White Balance) and MANU (Manual white balance)  
adjustments are provided. To select the desired mode, refer to the items “7.2 (3) WHT BAL (White balance)” and “7.  
MODE SETTING BY ON SCREEN DISPLAY”.  
AWB  
MANU  
(Automatic White Balance)  
(Manual White Balance)  
Outline Adjust white balance by displaying a white object Adjust the white balance manually using the WHT  
inside the area set by AWB menu and pressing BAL menu while shooting a white object.  
the [DATA UP] button.  
Note  
When the shutter mode is E.TRG, AWB is not Adjustment is performed by confirming with a  
available. monitor etc.  
AWB (Automatic white balance)  
• Set the MODE to AWB on the WHT BAL menu.  
Perform the C.TEMP (color temperature conversion) setting, if necessary.  
(Refer to the item “7.2 (3) WHT BAL (White balance)”.)  
3200K : Appropriate for indoor shooting.  
5600K : Appropriate for outdoor shooting.  
• If the index menu/menu is displayed, press the [DISP] button to disable the character display on the menu.  
• Shoot a known white object that fills the screen and push [DATA UP] button for approx. 1 second.  
• The character AWB blinks on the screen when the AWB starts.  
• The character AWB stops blinking when the AWB finishes, and the result is displayed for approx. 1 second.  
Result displayed  
Meaning  
AWB OK  
Automatic white balance adjustment finished correctly.  
AWB NG LEVEL Automatic white balance adjustment cannot be performed because the video level is too low.  
LOW Set the video level propely.  
AWB NG LEVEL Automatic white balance adjustment cannot be performed because the video level is too high.  
HIGH  
Set the video level propely.  
AWB NG  
C. TEMP LOW  
Automatic white balance adjustment cannot be performed because the color temperature is  
too low.  
If the C.TEMP is set to 5600K, set to 3200K.  
If the message appears with the C.TEMP set to 3200K, change the illumination or use a color  
temperature conversion filter.  
AWB NG  
C.TEMP HIGH  
Automatic white balance adjustment cannot be performed because the color temperature is  
too high.  
If the C.TEMP is set to 3200K, set to 5600K.  
If the message appears with the C.TEMP set to 5600K, change the illumination or use the  
color temperature conversion filter.  
AWB NG  
Automatic white balance adjustment cannot be performed because the shutter speed mode  
NOT AVAILABLE is E.TRG mode.  
AWB NG Automatic white balance adjustment cannot be performed for other reasons. Such as no  
white area is included in an object, etc.  
9
 
MANU (Manual white balance)  
• Set the MODE to MANU on the WHT BAL menu.  
(Refer to the item “7.2 (3) WHT BAL (white balance)”.)  
• Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the menu,  
confirming with a monitor etc.  
(Refer to the item “7.2 (3) (3.2) Changing the setting in MANU mode”.)  
5. 2 Gain  
When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level.  
For the gain adjustment of the unit, MANU (Manual) and OFF (0 dB) modes are provided. Select the mode on the  
GAIN menu. (Refer to the item “7.2 (2) GAIN (Video gain)”.)  
MANU (Manual gain)  
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0dB to 18dB in 1dB steps.  
(Refer to the item “7.2 (2) (2.1) (a) Changing the gain in MANU mode”.)  
OFF  
Gain is fixed at 0 dB.  
5. 3 Shading Correction  
Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom of the  
screen and at the corners. In this case, the shading correction can decrease the color shading. For the shading cor-  
rection of the unit, MANU (Manual shading correction) and OFF (no shading correction) modes for V.SHAD. (Vertical  
Shading) and C.SHAD. (Corner Shading) are provided. Select the mode on the SHADING menu. (Refer to the “7.2 (5)  
(5.2) Changing the manual V.SHAD. (Vertical Shading) correction setting” and “7.2 (5) (5.4) Changing the manual  
C.SHAD. (Corner Shading) correction setting”.)  
MANU (Manual Shading)  
Adjust the correction amount on the SHADING menu by confirming with a monitor or a waveform monitor.  
OFF  
The status is no shading correction.  
* The shading correction is effective when the lens iris or zoom ratio is fixed. Use the unit by setting V.SHAD.  
and C.SHAD. to OFF.  
10  
 
6. ITEMS CONTROLLED BY THE SCREEN DISPLAY  
Preset value  
(Factory setting)  
Item  
Available selections  
MANU, SS, E. TRG, AUTO  
MODE  
MANU  
E. TRG  
1P SNR, 1P SR, PW SNR, PW SR, RR  
1P SNR  
OFF, 1/100s, 1/250s, 1/500s, 1/1000s, 1/2000s,  
1/4000s, 1/10000s, 1/25000s, 1/50000s, 1/1000000s  
MANU speed  
OFF  
OFF  
Partial read OFF 1H/796H~795H/796H, OFF, 2FRM~512FRM  
Partial read 40fps 1H/580H~579H/580H, OFF, 2FRM~512FRM  
Partial read 42fps 1H/553H~552H/553H, OFF, 2FRM~512FRM  
Partial read 50fps 1H/465H~464H/465H, OFF, 2FRM~512FRM  
Partial read 60fps 1H/387H~386H/387H, OFF, 2FRM~512FRM  
Partial read 70fps 1H/332H~331H/332H, OFF, 2FRM~512FRM  
Partial read 80fps 1H/290H~289H/290H, OFF, 2FRM~512FRM  
Partial read 90fps 1H/258H~257H/258H, OFF, 2FRM~512FRM  
40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps  
Syncro.  
scan.  
Partial read  
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps,  
OFF  
E.80fps, E.90fps  
Trigger (1P SNR/SR)  
,
Trigger (PW SNR/SR)  
1P exposure time  
AUTO Level  
AUTO Peak/Average  
MODE  
,
0.01ms~30ms  
-100~0~100  
00:10~05:05~10:00  
MANU, OFF  
0dB~18dB  
AWB, MANU  
3200K, 5600K  
-100~0~100  
-100~0~100  
ON, OFF  
30 ms  
0
05:05  
OFF  
0dB  
AWB  
3200K  
0
0
OFF  
0
MANU  
MODE  
Color temperature  
MANUAL R GAIN  
MANUAL B GAIN  
GAMMA  
Master pedestal  
R pedestal  
-64~0~64  
-64~0~64  
0
B pedestal  
-64~0~64  
0
NR  
ON, OFF  
MANU, OFF  
OFF  
MANU  
0
V. Shading correction mode  
V. Shading manual correction MANU -128~0~127  
C. Shading correction mode  
C. Shading manual correction  
MANU R SIZE  
MANU R GAIN  
MANU R POSI  
MANU B SIZE  
MANU B GAIN  
MANU B POSI  
MANU, OFF  
MANU  
0~63  
0
0
0
0
0
0
-32~0~31  
-32~0~31  
0~63  
-32~0~31  
-32~0~31  
H phase adjustment  
-100~0~100  
0
Baud rate  
9600 bps, 19200 bps  
9600 bps  
11  
 
7. MODE SETTING BY ON SCREEN DISPLAY  
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The contents  
once set are memorized even if the power source is turned off, so it is unnecessary to set again when using the  
unit next time. When the setting is performed, select the menu of the item to be set. (Use an appropriate monitor to  
display an image with a higher signal format than XGA.)  
7. 1 Using the Menus  
When the power is turned on, the normal screen showing only the video signal appears. Change the output to each  
screen (video signal output, Index menu, and menus) by using the [DISP], [PAGE], [MENU UP], [MENU DOWN],  
[DATA UP], and [DATA DOWN] buttons.  
* A menu is selected when pushing the [PAGE] button after moving the “ ” on the screen by the [MENU UP], [MENU  
DOWN] button while the Index menu is displayed.  
POWER ON  
Video signal output  
Index menu  
DISP  
DISP  
DISP  
PAGE  
PAGE  
Menues  
PAGE  
SHADING  
WHT BAL  
PAGE  
AWB  
SHUTTER  
GAIN  
PROCESS  
SYNC  
INT  
OPTION  
BAUD  
RATE  
GAMMA  
ON  
V.SHAD.  
MANU  
PAGE  
MANU  
PAGE  
PAGE  
PAGE  
MANU  
SS  
PAGE  
GAMMA  
OFF  
V.SHAD.  
OFF  
EXT  
MANU  
OFF  
C.SHAD.  
MANU  
E. TRG  
1P SR  
PED  
MANU  
C.SHAD.  
OFF  
E. TRG  
1P SNR  
NR  
E. TRG  
PW SR  
E. TRG  
PW SNR  
E. TRG  
RR  
AUTO  
12  
 
7. 2 Menus  
• Select the menu to change the setting by referring to the item “7.1 Using the Menus”.  
• When the [MENU UP], [MENU DOWN] buttons are pushed, the “ ” on the screen moves up and down.  
Move the “ ” to the item whose setting you wish to change.  
Note:  
When performing the mode setting in the menu display while selecting ON in “PART” (Partial Read: refer to  
page 32) and E.TRG in “MODE”, the screen display and camera operation switch to normal mode. After closing  
the MENU, it returns to the previous mode.  
( 1 ) SHUTTER (Electronic shutter)  
The electronic shutter has four modes; MANU (Manual), SS (Synchro. Scan), E.TRG (External trigger), and AUTO  
(Auto Shutter).  
Move the “ ” to “MODE” and push [DATA UP], [DATA DOWN] button to select the desired mode among “MANU”, “SS”,  
“E.TRG”, and “AUTO”.  
MANUAL  
:
It is possible to select the exposure time from eleven speed setting; OFF, 1/100s, 1/250s, 1/500s,  
1/1000s, 1/2000s, 1/4000s, 1/10000s, 1/25000s, 1/50000s, 1/100000s.  
When not using the electronic shutter, select OFF.  
Note:  
When setting a rapid shutter speed, sensitivity degrades according to the speed.  
When a discharging light such as fluorescent lamp, etc. is used for the illumination, the flicker  
may be excessive.  
SS  
:
:
Shutter speed can be set by the horizontal scanning time (1H) unit or by the number of frames.  
E.TRG  
Exposure is performed and images are output by external trigger. E.TRG includes the five modes  
described below. (For details of specifications, refer to the item “7.4 E.TRG (External trigger)”.)  
• 1P SNR (1 Pulse Sync Non Reset)  
The charge begins to accumulate to each CCD pixels after the trigger pulse is received, and  
1 frame images are output according to the internal vertical sync signal timing. The exposure/  
accumulation time can be set from 0.01 to 30 ms. The trigger signal timing can be set to either the  
rising or falling edge.  
• 1P SR (1 Pulse Sync Reset)  
The charge begins to accumulate to each CCD pixels after the trigger pulse is received.  
Upon completion of accumulation the vertical sync signal is reset and 1 frame images are output.  
The exposure/accumulation time can be set from 0.01 to 30 ms. The trigger signal timing can be  
set to either the rising or falling edge.  
• PW SNR (Pulse width trigger Sync Non Reset)  
The charge begins to accumulate to each CCD pixels after the trigger pulse is received, and 1  
frame images are output according to the internal vertical sync signal timing. This is the mode to  
set the exposure period by the pulse width of the trigger. The trigger signal polarity can be set to  
either the positive or negative polarity.  
• PW SR (Pulse width trigger Sync Reset)  
The charge begins to accumulate to each CCD pixels after the trigger pulse is received.  
Upon completion of accumulation the vertical sync signal is reset and 1 frame images are output.  
This is the mode to set the exposure period by the pulse width of the trigger.  
The trigger signal polarity can be set to either the positive or negative polarity.  
• RR (Reset restart)  
Input of an external reset-restart signal permits one screen of information to be output at an arbi-  
trary timing.  
AUTO  
:
Exposure time is automatically controlled to obtain the specified video level.  
13  
 
(1. 1) Changing the setting in MANU mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
Shutter mode MANU, SS, E.TRG, AUTO  
SHUTTER  
• Shutter speed setting  
OFF, 100 (1/100s), 250 (1/250s), 500 (1/500s)  
1000 (1/1000s), 2000 (1/2000s), 4000 (1/4000s)  
10000 (1/10000s), 25000 (1/25000s)  
50000 (1/50000s)100000 (1/100000s)  
MODE  
MANU  
OUT.P  
MANU  
100  
OFF  
• Partial scanning switchPART switch)  
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps  
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps  
<MODE = MANUAL>  
(a) Changing the shutter speed  
aaMove the “ ” to MANU by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Partial scanning setting  
aaMove the “ ” to OUT.P by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the mode by pushing [DATA UP], [DATA DOWN] buttons.  
caaMove “ ” to the current value by pushing [MENU UP], [MENU DOWN] buttons.  
daaSelect a desired settings by pushing [DATA UP], [DATA DOWN] buttons.  
* The preset value of partial scanning is not displayed, when OUT.P is OFF.  
14  
 
(1. 2) Changing the setting in SS (synchro. scan) mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
SHUTTER  
MODE  
SS  
OUT.P  
SS  
OFF  
OFF  
• Shutter mode MANU, SS, E.TRG, AUTO  
• Synchro. scanning setting  
refer to the item "7.3 Synchro. Scan Operation".  
• Partial scanning switchPART switch)  
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps  
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps  
<MODE = SS>  
(a) Changing the shutter speed setting  
aaMove the “ ” to SS by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Partial scanning setting  
aaMove the “ ” to OUT.P by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the mode by pushing [DATA UP], [DATA DOWN] buttons.  
caaMove “ ” to the current value by pushing [MENU UP], [MENU DOWN] buttons.  
daaSelect a desired settings by pushing [DATA UP], [DATA DOWN] buttons.  
* The preset value of partial scanning is not displayed, when OUT.P is OFF.  
Note:  
The slow shutter speed may increase the fixed pattern noise and/or the white pixels. This is a characteristic of  
CCD, and is not a symptom of malfunction.  
15  
 
(1. 3) Changing the setting in E.TRG mode  
The E.TRG has five modes; 1P SNR, 1P SR, PW SNR, PW SR, RR.  
First move the “ ” to MODE and select E. TRG, then move the “ ” to E.TRG and select the desired E.TRG mode.  
( 1.3. 1) Changing the setting in 1P SNR mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG, AUTO  
SHUTTER  
• E.TRG mode  
1P SNR, 1P SR, PW SNR, PW SR, RR  
MODE  
E.TRG  
E.TRG  
TRG.P  
EXP.  
1P SNR  
• Input trigger pulse setting at 1P SNR and 1P SR  
Input trigger pulse : positive polarity  
Input trigger pulse : negative polarity  
30ms  
OFF  
OUT.P  
• Exposure time setting at 1P SNR and 1P SR  
0.01 ms  
0.01 ms 0.02 ms  
step step  
• Partial scanning switchPART switch)  
0.02 ms  
0.4 ms  
0.1 ms  
step  
1 ms  
20 ms  
1 ms 2 ms  
step step  
30 ms  
<MODE = E.TRG E.TRG = 1P SNR>  
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps  
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps  
(a) Changing the polarity of the input trigger pulse setting  
aaMove the “ ” to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect either  
,
by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing 1P SNR exposure time setting  
aaMove the “ ” to EXP. by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the exposure time by pushing [DATA UP], [DATA DOWN] buttons.  
(c) Changing the partial scanning setting  
aaMove the “ ” to OUT.P by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the mode by pushing [DATA UP], [DATA DOWN] buttons.  
caaMove “ ” to the current value by pushing [MENU UP], [MENU DOWN] buttons.  
daaSelect a desired settings by pushing [DATA UP], [DATA DOWN] buttons.  
* The preset value of partial scanning is not displayed, when OUT.P is OFF.  
16  
 
( 1.3. 2) Changing the setting in 1P SR mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG, AUTO  
SHUTTER  
• E.TRG mode  
1P SNR, 1P SR, PW SNR, PW SR, RR  
MODE  
E.TRG  
1P SR  
E.TRG  
TRG.P  
EXP.  
• Input trigger pulse setting at 1P SNR and 1P SR  
Input trigger pulse : positive polarity  
Input trigger pulse : negative polarity  
30ms  
OFF  
OUT.P  
• Exposure time setting at 1P SNR and 1P SR  
0.01 ms  
0.01 ms 0.02 ms 0.1 ms 1 ms  
step step step step  
• Partial scanning switchPART switch)  
0.02 ms  
0.4 ms  
1 ms  
20 ms  
30 ms  
2 ms  
step  
<MODE = E.TRG E.TRG = 1P SR>  
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps  
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps  
(a) Changing the polarity of the input trigger pulse setting  
aaMove the “ ” to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect either  
,
, by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing 1P SR exposure time setting  
aaMove the “ ” to EXP. by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the exposure time by pushing [DATA UP], [DATA DOWN] buttons.  
(c) Changing the partial scanning setting  
aaMove the “ ” to OUT.P by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the mode by pushing [DATA UP], [DATA DOWN] buttons.  
caaMove “ ” to the current value by pushing [MENU UP], [MENU DOWN] buttons.  
daaSelect a desired settings by pushing [DATA UP], [DATA DOWN] buttons.  
* The preset value of partial scanning is not displayed, when OUT.P is OFF.  
17  
 
( 1.3. 3) Changing the setting in PW SNR mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG, AUTO  
SHUTTER  
• E.TRG mode  
MODE  
E.TRG  
PW SNR  
1P SNR, 1P SR, PW SNR, PW SR, RR  
E.TRG  
TRG.P  
OUT.P  
• Input trigger pulse setting at PW SNR and PW SR  
OFF  
Input trigger pulse : positive polarity  
Input trigger pulse : negative polarity  
• Partial scanning switchPART switch)  
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps  
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps  
<MODE = E.TRG E.TRG = PW SNR>  
(a) Changing the polarity of the input trigger pulse setting  
aaMove the “ ” to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect either  
,
by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing the partial scanning setting  
aaMove the “ ” to OUT.P by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the mode by pushing [DATA UP], [DATA DOWN] buttons.  
caaMove “ ” to the current value by pushing [MENU UP], [MENU DOWN] buttons.  
daaSelect a desired settings by pushing [DATA UP], [DATA DOWN] buttons.  
* The preset value of partial scanning is not displayed, when OUT.P is OFF.  
Note:  
The longer the storage time with extended exposures, the more visible certain characteristics of CCD cameras  
become: fixed pattern noise, white pixels, etc.  
18  
 
( 1.3. 4) Changing the setting in PW SR mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG, AUTO  
SHUTTER  
• E.TRG mode  
MODE  
E.TRG  
PW SR  
1P SNR, 1P SR, PW SNR, PW SR, RR  
E.TRG  
TRG.P  
OUT.P  
• Input trigger pulse setting at PW SNR and PW SR  
OFF  
Input trigger pulse : positive polarity  
Input trigger pulse : negative polarity  
• Partial scanning switchPART switch)  
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps  
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps  
<MODE = E.TRG E.TRG = PW SR>  
(a) Changing the polarity of the input trigger pulse setting  
aaMove the “ ” to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect either  
,
by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The longer the storage time with extended exposures, the more visible certain characteristics of CCD cameras  
become: fixed pattern noise, white pixels, etc.  
( 1.3. 5) Changing the setting in RR mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG, AUTO  
SHUTTER  
• E.TRG mode  
MODE  
E.TRG  
OUT.P  
E.TRG  
RR  
OFF  
1P SNR, 1P SR, PW SNR, PW SR, RR  
• Partial scanning switchPART switch)  
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps  
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps  
<MODE = E.TRG E.TRG = RR>  
(a) Changing the partial scanning setting  
aaMove the “ ” to OUT.P by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the mode by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The longer the storage time with extended exposures, the more visible certain characteristics of CCD cameras  
become: fixed pattern noise, white pixels, etc.  
19  
 
(1. 4) Changing each setting in AUTO mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG, AUTO  
SHUTTER  
• Auto shutter level adjustment  
-100 ~ 100  
MODE  
LEVEL  
AUTO  
0
PEAK/AVE.  
00:10  
• Peak/Average ratio adjustment  
00:10 ~ 10:00  
<MODE = AUTO>  
(a) Changing the AUTO shutter level  
aaMove the “ ” to LEVEL by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the shutter level by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing the auto shutter detection (PEAK/AVE. ratio)  
aaMove the “ ” to PEAK/AVE. by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the PEAK/AVE. ratio by pushing [DATA UP], [DATA DOWN] buttons.  
( 2 ) GAIN (Video gain)  
When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level.  
For the gain adjustment of the unit, MANU (Manual) and OFF (0dB) modes are provided.  
aaMANU (Manual gain)  
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0dB to 18dB in 1dB steps.  
aaOFF  
Gain is fixed at 0dB.  
Move the “ ” to MODE, push the [DATA UP], [DATA DOWN], and select one of the two modes between MANU and OFF.  
(2. 1) Changing the setting in GAIN  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
GAIN  
MODE  
MANU  
MANU  
0dB  
• Gain mode MANU, OFF  
• Manual gain adjustment 0 dB to 18 dB (1 dB step)  
(a) Changing the gain in MANU mode  
aaMove the “ ” to MANU by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the manual gain by pushing [DATA UP], [DATA DOWN] buttons.  
20  
 
( 3 ) WHT BAL (White balance)  
WHT BAL has two modes; AWB, MANU.  
Move the “ ” to MODE, push the [DATA UP], [DATA DOWN], and select one of the two modes between AWB and  
MANU.  
(3. 1) Changing the setting in AWB (Automatic White Balance) mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
WHT BAL  
MODE  
AWB  
0
0
• White balance mode (AWB, MANU)  
R GAIN  
B GAIN  
C.TEMP  
Automatically adjusting value for red gain and blue gain  
are shown on the screen  
3200  
* These values may not be changed during AWB mode.  
• Color temperature setting 3200, 5600  
(a) Changing color temperature setting  
aaMove the “ ” to C.TEMP by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect either 3200 or 5600 by pushing [DATA UP], [DATA DOWN] buttons.  
(3. 2) Changing the setting in MANU (Manual) mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
WHT BAL  
MODE  
MANU  
• White balance mode AWB, MANU  
• Red gain adjustment -100 to 100  
• Blue gain adjustment -100 to 100  
• Color temperature setting 3200, 5600  
R GAIN  
B GAIN  
C. TEMP  
0
0
3200  
(a) Changing the red gain  
aaMove the “ ” to R GAIN by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the red gain by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing the blue gain  
aaMove the “ ” to B GAIN by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the blue gain by pushing [DATA UP], [DATA DOWN] buttons.  
21  
 
( 4 ) PROCESS  
• Gamma Correction (GAMMA)  
Select either OFF or ON of Gamma Correction.  
• Master Pedestal (M. PED)  
Adjust the Pedestal level of each RGB.  
• R Pedestal (R. PED)  
Adjust the Pedestal level of Red.  
• B Pedestal (B. PED)  
Adjust the Pedestal level of Blue.  
• Noise Reduction  
Select either OFF or ON of Noise Reduction.  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
PROCESS  
• Gamma correction ON/OFF  
• Master pedestal adjustment -64 to 64  
• R pedestal adjustment -64 to 64  
GAMMA  
M.PED  
R.PED  
B.PED  
NR  
OFF  
0
0
0
OFF  
• B pedestal adjustment -64 to 64  
• Noise reduction ON/OFF  
(4. 1) Changing gamma correction  
aaMove the “ ” to GAMMA by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the gamma correction by pushing [DATA UP], [DATA DOWN] buttons.  
(4. 2) Changing master pedestal  
aaMove the “ ” to M. PED by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the master pedestal by pushing [DATA UP], [DATA DOWN] buttons.  
(4. 3) Changing R pedestal  
aaMove the “ ” to R. PED by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the R pedestal by pushing [DATA UP], [DATA DOWN] buttons.  
(4. 4) Changing B pedestal  
aaMove the “ ” to B. PED by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the B pedestal by pushing [DATA UP], [DATA DOWN] buttons.  
(4. 5) Changing noise reduction  
aaMove the “ ” to NR by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the noise reduction by pushing [DATA UP], [DATA DOWN] buttons.  
22  
 
( 5 ) SHADING  
Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom of the  
screen and at the corners. In this case, the shading correction can decrease the color shading. For the shading  
correction of the unit, you can select among MANU (Manual shading correction) or OFF (no shading correction) for  
V.SHAD. (Vertical Shading) and C.SHAD. (Corner Shading).  
MANU (Manual Shading correction)  
Adjust the correction amount on the SHADING menu by confirming with a monitor or a waveform monitor.  
• R size (R SIZE)  
Adjust the red correction area of the corner.  
low  
0
high  
63  
• R gain (R GAIN)  
Adjust the red correction level. -32  
low  
high  
31  
• R position (R POSI)  
Adjust the red correction area on left and right side.  
• B size (B SIZE)  
Left low  
Right low  
31  
-32  
Adjust the blue correction area of the corner.  
• B gain (B GAIN)  
Adjust the blue correction level.  
• B position (B POSI)  
Adjust the blue correction area on left and right side.  
OFF  
The status is no shading correction.  
* The shading correction is effective when the lens iris or zoom ratio is fixed. Use the unit by setting V.SHAD  
and C.SHAD. to OFF.  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
SHADING  
• Vertical Shading mode setting (MANU/OFF)  
• Manual Vertical Shading mode adjustment -128 to 127  
• Corner Shading mode setting (MANU/OFF)  
V.SHAD.  
MANU  
MANU  
0
C.SHAD.  
R SIZE  
R GAIN  
R POSI  
B SIZE  
B GAIN  
B POSI  
MANU  
• R size adjustment  
• R gain adjustment  
• R position adjustment  
• B size adjustment  
• B gain adjustment  
• B position adjustment  
0 to 63  
0
0
0
0
0
0
-32 to 31  
-32 to 31  
0 to 63  
-32 to 31  
-32 to 31  
23  
 
(5. 1) Changing V.SHAD. (Vertical Shading) correction mode  
aaMove the “ ” to V.SHAD by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the V.SHAD. mode setting by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The alignment value for vertical shading is fixed to “0” when selecting V.SHAD. OFF.  
MANU is not displayed in the menu.  
(5. 2) Changing the manual V.SHAD. (Vertical Shading) correction setting  
aaMove the “ ” to MANU by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the MANU V.SHAD. by pushing [DATA UP], [DATA DOWN] buttons.  
(5. 3) Changing C.SHAD. (Corner Shading) correction mode  
aaMove the “ ” to C.SHAD by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect the C.SHAD. mode setting by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The alignment value for corner shading is fixed to “0” when selecting C.SHAD. OFF.  
MANU is not displayed in the menu.  
(5. 4) Changing the manual C.SHAD. (Corner Shading) correction setting  
(a) Changing the red size setting  
aaMove the “ ” to R SIZE by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the R size by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing the red gain setting  
aaMove the “ ” to R GAIN by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the R gain by pushing [DATA UP], [DATA DOWN] buttons.  
(c) Changing red position setting  
aaMove the “ ” to R POSI by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the R position by pushing [DATA UP], [DATA DOWN] buttons.  
(d) Changing blue size setting  
aaMove the “ ” to B SIZE by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the B size by pushing [DATA UP], [DATA DOWN] buttons.  
(e) Changing blue gain setting  
aaMove the “ ” to B GAIN by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the B gain by pushing [DATA UP], [DATA DOWN] buttons.  
(f) Changing blue position setting  
aaMove the “ ” to B POSI by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the B position by pushing [DATA UP], [DATA DOWN] buttons.  
24  
 
( 6 ) SYNC  
When an external sync signal is input, the display menu changes from INT (internal sync) to EXT (external sync)  
automatically.  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
SYNC  
MODE  
EXT  
• Sync system display  
H PHASE  
0
• H PHASE adjustment -100 to 100  
(6. 1) Adjusting horizontal phase  
aaMove the “ ” to H PHASE by pushing [MENU UP], [MENU DOWN] buttons.  
aaAdjust the horizontal phase by pushing [DATA UP], [DATA DOWN] buttons.  
( 7 ) OPTION  
(7. 1) Changing serial communication baud rate  
aaMove the “ ” to BAUD RATE by pushing [MENU UP], [MENU DOWN] buttons.  
aaSelect either 9600 or 19200 by pushing [DATA UP], [DATA DOWN] buttons.  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
OPTION  
BAUD RATE  
9600  
• Serial baud rate setting 9600, 19200  
Communication speed setting.  
Set the speed to the baud rate setting  
on the personal computer side.  
( 8 ) Returning to factory settings  
All the settings can be returned to the factory default status (preset status).  
(1) If characters are displayed on the screen, press the [DISP] button to disable the character display.  
(2) Push [MENU DOWN] and [DATA DOWN] buttons simultaneously for approx. 1 second.  
(3) The preset operation starts. When the preset operation finishes, the character PRESET OK is displayed for  
approx. 1 second.  
25  
 
7. 3 Synchro. Scan Operation  
The shutter speed can be set by the horizontal scanning period (1H) or by the number of frames.  
( 1 ) Setting by 1H  
1H/796H ~ 795H/796H stands for the setting by the 1H and the shutter speed can be set by the 1H (43.05 µs).  
When operating Partial Scanning or binning, the number’s listed below can be used for setting.  
Partial scanning OFF  
1H/796H ~ 795H/796H  
1H/580H ~ 579H/580H  
1H/553H ~ 552H/553H  
1H/465H ~ 464H/465H  
1H/387H ~ 386H/387H  
1H/332H ~ 331H/332H  
1H/290H ~ 289H/290H  
1H/258H ~ 257H/258H  
Partial scanning 40fps, E.40fps  
Partial scanning 42fps, E.42fps  
Partial scanning 50fps, E.50fps  
Partial scanning 60fps, E.60fps  
Partial scanning 70fps, E.70fps  
Partial scanning 80fps, E.80fps  
Partial scanning 90fps, E.90fps  
( 2 ) Setting by the frame  
2FRM to 512FRM stand for the setting (long period exposure) by the frame.  
The video signal stored during the frame period set is output as 1 frame video image at a frame interval specified.  
(Internal VD)  
n
n+1  
RGB data  
(video interval image)  
FVAL  
LVAL,  
DAVL  
(4FRM setting)  
26  
 
7. 4 E.TRG (External trigger)  
Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, and 1 frame images are output.  
There are four modes: 1P SNR, 1P SR, PW SNR, PW SR.  
( 1 ) 1P SNR (1 Pulse Trigger Sync Non Reset)  
Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, and 1 frame images are output.  
(1. 1) 1 Pulse Trigger SYNC-NON RESET Picture Output Timing  
Negative polarity mode  
Trigger*1  
Positive polarity mode  
About 1 µs  
Exposure period*2  
Exposure period*2  
External HD IN*1  
External VD IN*1  
About 1H  
(Internal VD)  
RGB data  
(video interval image)  
FVAL  
LVAL,  
DVAL  
4
*
28H (Partial scanning OFF)  
25H (Partial scanning 40fps)  
27H (Partial scanning 42fps)  
33H (Partial scanning 50fps)  
39H (Partial scanning 60fps)  
43H (Partial scanning 70fps)  
46H (Partial scanning 80fps)  
48H (Partial scanning 90fps)  
The internal VD falling edge is within the  
exposure period and thus video is not output. *3  
*1: External input signal  
*2: Exposure time is determined by the setting of “7. 2 (1.3) Changing the setting in E.TRG mode”.  
*3: Video is output at the falling edge of the internal VD following completion of the exposure period.  
The video and FVAL/LVAL/DVAL have a paired relationship.  
*4: When NR is set to ON, 1H is increased.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trigger, there  
will be an effect on the video.  
27  
 
( 2 ) 1P SR (1 Pulse Trigger Sync Reset)  
Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, the vertical sync signal is reset  
and frame images are output.  
(2. 1) 1 Pulse Trigger SYNC-RESET Picture Output Timing  
Negative polarity mode  
Trigger*1  
Positive polarity mode  
About 1 µs  
Exposure period*2  
Exposure completion  
0 to 1H*3  
(Internal VD)  
RGB data  
(video interval image)  
FVAL  
LVAL,  
DVAL  
4
*
28H (Partial scanning OFF)  
25H (Partial scanning 40fps)  
27H (Partial scanning 42fps)  
33H (Partial scanning 50fps)  
39H (Partial scanning 60fps)  
43H (Partial scanning 70fps)  
46H (Partial scanning 80fps)  
48H (Partial scanning 90fps)  
*1: External input signal  
*2: Exposure time is determined by the setting of “7. 2 (1.3) Changing each setting in E.TRG mode”.  
*3: VD is generated after 0 to 1H following the completion of the exposure period and the video is synchronized to  
this and output.  
*4: When NR is set to ON, 1H is increased.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trigger, there  
will be an effect on the video.  
28  
 
( 3 ) PW SNR (Pulse width trigger SYNC-NON RESET)  
The trigger input to CC1 of the DIGITAL terminal develops 1 frame images.  
(3. 1) Pulse Width Trigger SYNC-NON RESET Picture Output Timing  
Negative polarity mode  
Positive polarity mode  
Trigger*1  
About 7 µs  
About 1 µs  
Exposure period*2  
Exposure period*2  
External HD IN*1  
External VD IN*1  
(Internal VD)  
About 1H  
RGB data  
(video interval image)  
FVAL  
LVAL,  
DVAL  
4
*
28H (Partial scanning OFF)  
25H (Partial scanning 40fps)  
27H (Partial scanning 42fps)  
33H (Partial scanning 50fps)  
39H (Partial scanning 60fps)  
43H (Partial scanning 70fps)  
46H (Partial scanning 80fps)  
48H (Partial scanning 90fps)  
The internal VD falling edge is within the  
exposure period and thus video is not output. 3  
*
*1: External input signal  
*2: Exposure time = Trigger pulse width + 6 µs  
(Valid trigger pulse width is 2 µs or greater for external trigger shutter operation.)  
*3: Video is output at the falling edge of the internal VD following completion of the exposure period.  
The video and FVAL/LVAL/DVAL have a paired relationship.  
*4: When NR is set to ON, 1H is increased.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trigger, there  
will be an effect on the video.  
29  
 
( 4 ) PW SR (Pulse width trigger SYNC-RESET)  
The trigger input to the CC1 of the DIGITAL terminal develops 1 frame images.  
(4. 1) 1 Pulse Width Trigger SYNC-RESET Picture Output Timing  
Negative polarity mode  
Positive polarity mode  
Trigger*1  
About 1 µs  
About 7 µs  
Exposure period*2  
Exposure completion  
0 to 1H  
3
(Internal VD)  
*
RGB data  
(video interval image)  
FVAL  
LVAL,  
DVAL  
4
*
28H (Partial scanning OFF)  
25H (Partial scanning 40fps)  
27H (Partial scanning 42fps)  
33H (Partial scanning 50fps)  
39H (Partial scanning 60fps)  
43H (Partial scanning 70fps)  
46H (Partial scanning 80fps)  
48H (Partial scanning 90fps)  
*1: External input signal  
*2: Exposure time = Trigger pulse width + 6 µs  
(Valid trigger pulse width is 2 µs or greater for external trigger shutter operation.)  
*3: VD is generated after 0 to 1H following the completion of the exposure period and the video is synchronized to  
this and output.  
*4: When NR is set to ON, 1H is increased.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trigger, there  
will be an effect on the video.  
30  
 
( 5 ) RR (Reset restart)  
Input of an external reset-restart signal (CC4 of the DIGITAL terminal: External VD input) permits one screen of  
information to be output at an arbitrary timing.  
(5. 1) Long Term Exposure  
When sufficient sensitivity is not obtained under normal operating conditions or capturing the trail of a moving object  
is desired, the reset-restart function allows high-sensitivity images by extending the exposure time. To achieve this,  
please input (from an external source) a VD signal that has an expanded VD pulse and VD pulse interval.  
(5. 2) Input Timing Chart Example  
External HD IN  
External VD IN  
V reset  
V reset  
About 1H  
About 1H  
(Internal VD)  
Exposure period  
Exposure period  
Exposure period  
RGB data  
(video interval image)  
FVAL  
LVAL,  
DVAL  
1 frame  
1 frame= 796H (Partial scanning OFF)  
580H (Partial scanning 40fps)  
553H (Partial scanning 42fps)  
465H (Partial scanning 50fps)  
387H (Partial scanning 60fps)  
332H (Partial scanning 70fps)  
290H (Partial scanning 80fps)  
258H (Partial scanning 90fps)  
Note:  
External VD interval: more than 1 frame  
31  
 
7. 5 Partial Read  
( 1 ) Partial Scanning OFF (All pixels scanning)  
In this mode, every pixels independent signal is output from the DIGITAL connector each 1/29.2s.  
Video interval  
image  
1/29.2s (796H)  
( 2 ) Partial Scanning ON  
In this mode, the pixel signal of the vertical center portion of the image is output from the DIGITAL connector.  
In the E. fps mode, the partial scanning and all the pixels scanning can be switched by the DIGITAL terminal (CC2:  
partial scanning control signal).  
CC2  
E.40fps  
E.42fps  
Partial scanning 42fps  
All pixels scanning  
E.80fps  
E.50fps  
Partial scanning 50fps  
All pixels scanning  
E.90fps  
E.60fps  
LPartial scanning 40fps  
‘H’ All pixels scanning  
Partial scanning 60fps  
All pixels scanning  
CC2  
E.70fps  
LPartial scanning 70fps  
‘H’ All pixels scanning  
Partial scanning 80fps  
All pixels scanning  
Partial scanning 90fps  
All pixels scanning  
Video interval  
image  
1/40s (580H):When 40fps is selected  
1/42s (553H):When 42fps is selected  
1/50s (465H):When 50fps is selected  
1/60s (387H):When 60fps is selected  
1/70s (332H):When 70fps is selected  
1/80s (290H):When 80fps is selected  
1/90s (258H):When 90fps is selected  
32  
 
( 3 ) When Partial Scanning Mode is ON  
(Internal VD)  
FVAL  
LVAL,  
DVAL  
RGB data  
(video interval image)  
Blanking interval  
Video interval Blanking interval  
B
C
D
Total  
A
Video period  
Mode  
40fps  
42fps  
50fps  
60fps  
70fps  
80fps  
90fps  
Total A  
580H  
553H  
465H  
387H  
332H  
290H  
258H  
Blanking interval B  
Video interval C  
542H  
Blanking interval D  
25H  
27H  
33H  
39H  
43H  
46H  
48H  
13H  
14H  
20H  
26H  
30H  
33H  
35H  
512H  
412H  
322H  
259H  
211H  
175H  
33  
 
7. 6 External Sync  
When using the unit with an external sync signal, input HD and VD to CC3 and CC4 of the DIGITAL terminal.  
When the external sync signal is input, the camera automatically switches its sync from the internal sync to the  
external sync.  
The operation is as shown below, depending on the unit’s status and how external sync signals are input.  
Shutter mode  
At time of SYNC-NON  
RESET mode  
HD input VD input  
Note  
N
Y
N
Y
N
Y
Y
N
Internal sync mode  
External sync mode  
Only V reset is applied due to VD input. Normally not used.  
HD is synchronized to external, but video is not output because  
there is no VD input. Normally not used.  
At time of SYNC-  
RESET mode  
N
Y
Internal sync mode. The presence of VD is ignored, and after a  
specified time after a trigger input, V reset is applied.  
HD is synchronized to external. The presence of VD is ignored,  
and after a specified time after a trigger input, V reset is applied.  
HD is synchronized to external. Video is output due to VD input.  
HD is synchronized to the inside of the camera. Video is output  
due to VD input.  
*
*
At time of reset restart  
Y
N
Y
Y
N
Video is not output because there is no VD input. Normally not  
used.  
*
At time of manual  
shutter  
N
Y
Y
N
N
Y
N
Y
Internal sync mode  
External sync mode  
HD is synchronized to external. Normally not used.  
Disabled  
Either Y or N is permitted.  
*
( 1 ) External sync signal polarity  
HD: 2 to 5V(p-p) Negative  
VD: 2 to 5V(p-p) Negative  
( 2 ) External sync frequency range  
(External sync with HD, VD)  
Within ±1% (at horizontal sync frequency of 23.229 kHz)  
( 3 ) Using the unit with external sync signal  
When adjusting H (horizontal) phase refer to the item “7.2 (6) (6.1) Adjusting horizontal phase”.  
(3. 1) H (horizontal) phase adjustment  
External  
Sync. signal  
Observe the external sync signal and the LVAL signal output waveform  
of the unit with a dual trace oscilloscope, and adjust H phase so that  
Match  
the H phases match.  
the phase.  
LVAL signal  
output  
34  
 
8. INPUT OUTPUT SIGNAL SPECIFICATIONS  
( 1 ) HD Input Specifications  
( 2 ) VD Input Specifications  
2.0µs 5.0µs  
5H 21H  
( 3 ) Trigger Pulse Specifications  
(Positive polarity mode)  
More than 2 µs  
(Negative polarity mode)  
More than 2 µs  
( 4 ) External HD/VD Input Phase Specifications  
External VD  
falling edge  
100  
100  
External HD  
Unit : Clock  
1 clk=33.9ns  
Center  
The phase relationship of the external HD and VD should correspond to the center phase (i.e., the external HD fall-  
ing edge) as illustrated in the above diagram.  
External VD falling edge:  
Please input within about 100 clock cycles of the standard center phase.  
Note that V sync of the video is output with a delay of about 2H from the external VD at the time of reset-restart  
and the external trigger mode.  
In the normal mode:  
Continuously with the HD period of 43.05 μs and VD period of 34.27 ms (partial scanning 40fps: 24.97 ms, 42fps:  
23.81 ms, 50fps: 20.02 ms, 60fps: 16.66 ms, 70fps: 14.29ms, 80fps: 12.49 ms, 90fps: 11.11 ms).  
Phase timing is as illustrated in the above diagram (with only the falling edge applicable).  
In the reset-restart/external trigger mode:  
Continuously with the HD period of 43.05 μs. VD (reset) is at an arbitrary timing with the phase of HD being within  
the standard of the above diagram.  
35  
 
9. CCD OUTPUT WAVEFORM TIMING CHART  
( 1 ) Horizontal Output Waveform Timing Chart  
One horizontal scan interval 1270 clk  
(43.05 µs)  
LVAL,  
DVAL  
246 clk  
(8.34µs)  
33.9 ns  
29 clk 3 clk  
40 clk  
164 clk  
CCD  
output signal  
5 clk  
5
clk  
Optical black Horizontal transfer Dummy  
portion  
stop interval  
pixels  
Total effective pixels 1034 clk  
Optical black  
portion  
1
Horizontal blanking interval 246 clk  
*
Output video interval 1024 clk  
(8.34 µs)  
(34.71 µs)  
RGB data  
Pixel  
Clock  
clk=33.9 ns  
(29.5 MHz)  
*1: Invalid data are output during a horizontal blanking interval.  
( 2 ) Vertical Output Waveform Timing Chart  
796H  
28H  
(1205µs)  
FVAL  
LVAL,  
DVAL  
768H  
CCD  
output signal  
1
1
2
3
4
5
6
7
1
1
2
3
4
5
6
7
Dummy  
pixels  
Dummy  
pixels  
Optical black  
portion  
Optical black  
portion  
Optical black  
portion  
Optical black  
portion  
Vertical blanking interval 28H  
Vertical blanking interval 28H  
(1205µs)  
(1205µs)  
RGB data  
36  
 
10. BEFORE MAKING A SERVICE CALL  
Symptom  
Items to be checked  
No image  
• Is the power supplied correctly?  
• Is the lens iris adjusted correctly?  
• Are the cables connected correctly?  
• Is the shutter mode set correctly?  
• Is the image process equipment set correctly?  
Poor color  
• Is the monitor adjusted correctly?  
• Is the white balance of the camera adjusted correctly?  
• Is there enough illumination?  
11. SPECIFICATIONS  
Power supply  
DC 10V ~ DC 13.2V  
Power consumption  
Pick-up system  
Image sensor  
Approx. 3.1W (When the DC power supply is 12V)  
RGB, 3CCD  
1/3inch All pixels CCD  
(Effective pixels Horizontal : 1034, Vertical : 779)  
Scanning System  
Video output pixels  
Pixel clock frequency  
Sync signal frequency  
Sync system  
Progressive scan  
Horizontal pixels : 1024, Vertical : 768  
29.5MHz  
Horizontal : 23.229kHz, Vertical : 29.18Hz  
Internal/External (Automatic switching)  
F6.8 standard (2000 lx, 3000K)  
14 lx (F2.2, Sensitivity + 18 dB, 3000K)  
C mount (flange back : 17.526 mm in-air)  
0 to 40°C (32 to 104°F)  
Sensitivity  
Minimum illumination  
Lens mount  
Ambient temperature  
Ambient humidity  
Weight  
Less than 90%  
Approx. 158g (0.338lbs)  
External dimension  
44 (W) x 44 (H) x 78 (D) mm  
(1.73” (W) x 1.73” (H) x 3.07” (D)) (except for protruded portion)  
White balance  
Gain  
AWB (Automatic white balance), MANUAL (Manual)  
MANUAL (Manual), OFF (0 dB)  
Partial scanning  
Output signal  
Sync signal output  
40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps  
8-bit RGB, Digital output (Camera Link format)  
FVAL, LVAL, DVAL (Positive polarity)  
Pixel Clock  
External sync input  
HD : CC3 (LVDS input) Negative polarity  
VD : CC4 (LVDS input) Negative polarity  
External trigger input  
CC1 (LVDS input), More than 2 μs pulse width  
Partial scanning control CC2 (LVDS input)  
signal input  
Interface  
Serial data interface : Ser TC (RXD), Ser TFG (TXD)  
The designs and specifications are subject to change without notice.  
If any change occurs, we will revise the manual, etc.  
37  
 
12. EXTERNAL APPEARANCE DIAGRAM  
Unit : mm [inch]  
5
[0.20]  
2-M3 Depth 3  
78  
[3.07]  
6.3  
[0.25]  
12  
[0.47]  
44  
[1.73]  
19.2  
[0.76]  
2-M2  
5
56  
[2.20]  
4-M3 Depth 3  
[0.20]  
25  
[0.98]  
25  
[0.98]  
4-M2 Depth 3  
inch=mm/25.4  
38  
 
39  
 
Limited Warranty – TOSHIBA CCD Camera  
The Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD") makes the following limited warranty  
with regard to this CCD Camera ("Product"). These limited warranties apply to the Original End-User ("You").  
One (1)Year Limited Warranty of Labor and Parts  
ISD warrants that this Product will perform in accordance with specifications for a period of one (1) year from the date of  
purchase by the Original End-User. During this one (1) year period, ISD will repair or replace the Product, if it does not  
perform as warranted. In order to take advantage of this Limited Warranty, You must: (a) deliver the Product to an ISD  
Authorized Service Provider ("ASP"); and (b) pay all transportation and insurance charges for shipment of the Product to the  
ASP. ISD reserves the right to substitute factory refurbished parts in place of those in need of repair.  
Instruction Manual (Owner’s Manual):  
You should read the Instruction Manual (Owner’s Manual) thoroughly before operating this Product. Before seeking warranty  
service, you should check the troubleshooting guide in the Instruction Manual (Owner’s Manual) and follow the instructions to  
correct the problem.  
Your Responsibilities  
This Limited Warranty is subject to the following conditions:  
1. You must provide the bill of sale or proof of purchase at the time that warranty service is required.  
2. You must notify an ASP within thirty (30) days after You discover that the Product does not perform in accordance with  
specifications during the Limited Warranty period.  
3. All warranty servicing of this product must be made by an ISD Authorized Service Provider.  
4. You must pack the Product in its original carton using the original packing material, then insert the original carton  
containing the Product into another carton with additional packing material before shipping the Product to an ASP.  
DISCLAIMERS:  
ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. SOME STATES DO  
NOT ALLOWTHE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY  
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TOYOU.  
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR SOLE AND EXCLUSIVE  
REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ISD OR ITS PARENT  
COMPANY OR ANY ASP BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE  
PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION APPLIES TO DAMAGES OF ANY KIND, INCLUDING ANY  
DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST SAVINGS OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY  
OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF CONTRACT, TORT OR OTHERWISE, OR WHETHER  
ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF ISD, ITS PARENT COMPANY, OR  
AN ASP HAS BEEN ADVISED OFTHE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY.  
SOME STATES DO NOT ALLOWTHE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES  
FOR SOME PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TOYOU.  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS  
WHICH MAY VARY FROM STATE TO STATE.  
THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE,  
ABUSE, ACCIDENT, IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE IN VIOLATION OF ISD’S  
WRITTEN INSTRUCTIONS, OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD’S PRIOR  
AUTHORIZATION, OR UPON THE REMOVAL OR ALTERATION OF ISD’S FACTORY SERIAL NUMBER. LABOR  
SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND ADJUSTMENT OF CONTROLS ARE NOT  
COVERED BY THIS LIMITED WARRANTY.  
How to Obtain Warranty Service – Step-By-Step Procedures:  
To obtain warranty service, You should:  
1. Contact an ASP for warranty service within thirty (30) days after the Product fails to comply with specifications.  
2. Arrange for shipment of the Product to an ASP.  
3. Securely pack the Product as described above, insure the carton, and include a letter explaining the problem and a copy  
of the bill of sale or proof of purchase.  
4. Prepay all transportation and insurance costs.  
Questions? If you have any questions, please check ISD’s Web Site for support and a current e-mail contact to where  
you can send e-mails:  
No person, agent, distributor, dealer, authorized service provider, or company is authorized to change, modify, or extend the  
terms of this Limited Warranty in any manner whatsoever. The time within which an action must be commenced to enforce  
any obligation of ISD arising under this Limited Warranty or under any statute, or law of the United States or any state thereof,  
is hereby limited to one (1) year from the date You discover or should have discovered the problem. This limitation does not  
apply to implied warranties arising under state law. Some states do not permit limitation of the time within whichYou may bring  
an action beyond the limits provided by state law, so the above provision may not apply to You. This Limited Warranty gives  
You specific legal rights and You may also have other rights which vary from state to state.  
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.  
Imaging Systems Division  
9740 Irvine Boulevard, Irvine, CA 92618-1697  
Copyright© 2012 Toshiba America, Inc. All rights reserved.  
 

Teledex Telephone Diamond+Plus User Manual
Tempo Telephone DSTS2 User Manual
TERK Technologies Stereo System TV32 User Manual
Timex Watch 791 095003 User Manual
Toshiba Personal Computer TECRA M9 User Manual
Toshiba Projector TLP451U User Manual
Ultimate Support Systems Musical Toy Instrument GS 200 User Manual
Uniflame Charcoal Grill CBC1232SP User Manual
ViewSonic Projector pjl9371 User Manual
Virgin Mobile Laptop VMFNM0609 User Manual